La Crosse Technology WS-7213U Instrukcja Użytkownika

WS-7213U Wireless 433 MHz Weather Station Instruction Manual

10 B. INDOOR WEATHER STATION Note: After the batteries are installed, DO NOT press any buttons for 15 minutes. This may interfere with the signals,

11 5. The indoor weather station should now show: “-:- -” in the TIME LCD, indoor temperature in the INDOOR LCD and outdoor temperature and humidity

12 FEATURES A. MINIMUM AND MAXIMUM TEMPERATURES 1. Press and release the “MIN/MAX” button, “MAX” appears at the bottom of the display and the recor

13 displayed. B. RESETTING THE MINIMUM AND MAXIMUM TEMPERATURES To reset both the minimum and maximum temperatures—press and hold the “MIN/MAX” butto

14 C. WEATHER FORECAST The weather forecasting feature is estimated to be 75% accurate. The weather forecast is based solely upon the change of air

15 1. Weather Icons There are 3 possible weather icons that will be displayed in the FORECAST LCD: Sunny—indicates that the weather is expected

16 The weather icons change when the unit detects a change in air pressure. The icons change in order, from “sunny” to “partly sunny” to “cloudy” or

17 pointing down indicates that the air pressure is decreasing and the weather is expected to become worse or remain poor. No arrow means the pressur

18 monitor the temperature via a probe for use in pools, spas, etc and the TX4U will monitor temperature and humidity. Note: When setting up multip

19 procedures seen in section “I” of the Detailed Set-Up Guide) into the remote sensors. 5. Install batteries into the indoor weather station. Follow

2 TABLE OF CONTENTS Topic Page Inventory of Contents 3 Additional Equipment 4 Quick Setup 5-8 Detailed Setup Guide Battery Installation 9-11 Se

20 2. To view the Minimum/Maximum temperature: first select from which remote temp/humidity sensor to read data from (indicated by the “boxed” number

21 MOUNTING Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temp/humidity se

22 B. THE WEATHER STATION 1. The indoor weather station comes with the table stand already mounted. If you wish to use the table-stand, all that is

23 TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www.lacrossetechnol

24 3) Once the system has been reset and you have a temperature and humidity reading from the sensor, temporarily place the remote temp/humidity sen

25 Problem: Temperatures do not match if units are placed next to each other. Solution: Each temp/humidity sensor is manufactured to be accurate to w

26 compensate for the above factors and obtain an accurate comparison. MAINTENANCE AND CARE INSTRUCTIONS • Extreme temperatures, vibration, and sh

27 SPECIFICATIONS Transmitting Frequency 433MHz Measuring Range - Temperature Indoor Weather Station: Indoor 32°F to 140°F with 0.1°F resolution. Ind

28 Transmitting range: Maximum 80 feet (25m) open space Batteries—(Alkaline recommended) Remote Temp/Humidity Sensor 2 x AA, 1.5V Indoor Weather Stat

29 This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the orig

3 INVENTORY OF CONTENTS 1. The indoor weather station (Figure 1) 2. The remote temperature/humidity sensor (TX4U) and mounting bracket. (Figure 2)

30 Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay ground return shipping charg

31 LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATIO

32 web: www.lacrossetechnology.com FCC DISCLAIMER This device complies with part 15 of the FCC rules. Operation is subject to the following two con

1WS-7034U Wireless 433 MHz Temperature Station Instruction Manual

2TABLE OF CONTENTS Topic Page Inventory of Contents 1 Quick Setup 2 Detailed Setup Guide Battery Installation 3-4 Setting the Time 5 Selecting

1INVENTORY OF CONTENTS 1. The Indoor Temperature Station (Figure 1) 2. The Remote Control Sensor (TX2U) and mounting bracket. (Figure 2) 3. 3 each

2QUICK SETUP 1. Insert two AAA batteries into the Remote Control Sender. 2. Insert two AAA batteries into the Indoor Temperature Station. 3. Wait

3DETAILED SETUP GUIDE I. BATTERY INSTALLATION A. REMOTE CONTROL SENDER 1. Remove the mounting bracket. 2. Remove battery cover 3. Observing the

4Battery Cover 1. Remove the battery cover on the backside. To do this, push up and pull out. 2. Observing the correct polarity, install 2 AA bat

5II. TIME A. SETTING THE TIME 1. Press and hold the SET button for 1 second. “12h” will appear in the TIME LCD. 2. Use the MIN/MAX button to select

4 ADDITIONAL EQUIPMENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AA 1.5V batteries. (for the indoor weather station) 3. 2 Fresh AA 1.5

6III. UNITS OF TEMPERATURE MEASURE A. SELECTING UNITS OF MEASUREMENT 1. Press and hold the SET button for 1 second. 2. Press the SET button again. “

7minimum outdoor temperature, and maximum outdoor temperature. The time of occurrence of the value for outdoor temperature will also flash. B. RESET

8TX2U will monitor temperature only, a TX3U will monitor temperature and display the temperature on its LCD, and the TX3UP will monitor the temperatu

96. In sequential order, install batteries (follow the same battery installation procedures seen in section I. A) of the Detailed Set-Up Guide). 7. I

10maximum indoor temperature, and the minimum and maximum outdoor temperature. 3. To reset the Minimum/Maximum readings press and the MIN/MAX button

111. The Indoor Temperature Station comes with the table stand already mounted. If you wish to use the table-stand all that is required is to place

121) Set the LCD contrast to a higher number 2) Replace batteries Problem: No outdoor temperature is displayed. Solution: 1) Remove all batteries,

13sensor is less responsive to ambient air currents because of the shielding effect of the display's case. In addition, the case can act as a he

14scouring agents; they may mark the displays and casings. • Do not submerge in water. • Do not subject the units to unnecessary heat or cold by pl

15Transmitting range Maximum 80 feet (25m) open space. Temperature check Indoor Every 10 seconds. Outdoor Three times in 10 minutes. Batteries

5 QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor weather station and remote temp/humid

16service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can only be perfo

17Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused b

18INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF CHILDREN’S REACH. This warranty gives you specific legal rights. You may also have other ri

19 FCC DISCLAIMER This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may

6 In this time the indoor weather station and remote temp/humidity sensor will start to talk to each other and the displays will show both the indoor

7 Notes on Outdoor Sensor Placement The remote temp/humidity sensor should be placed in a dry, shaded area. Fog and mist will not harm your remote

8 To complete the set up of your indoor weather station after the 10 minutes have passed, please follow the steps below. 1. Press and hold the “SET

9 Battery compartment DETAILED SETUP GUIDE I. BATTERY INSTALLATION A. REMOTE TEMP/HUMIDITY SENSOR 1. Remove the mounting bracket. 2. Re